REALITi 360 Version 11.8.0 is here
| By iSimulate
The latest REALITi 360 Version 11.8.0 is here!
Improvements
Atlas
- Updated Atlas Junior compression depth mapping
- Fixed data not being sent from Atlas Junior after firmware update screen opens after connection (not a problem in previous versions)
- Changed the disconnect timeout fix for Atlas Junior to be for any version after V2
- Updated Atlas Baby’s adequate and maximum depth values (if the user has changed this previously on control then the values won’t change)
- Fixed clearing of Atlas Junior/Baby wifi config from the available list on scan
- Rounding volume for Atlas Baby. Removed random variation of volume for Baby and Junior.
- Added more compression idle checks for junior/baby: if the depth is low or there are no packets for more than 0.4s or the depth is repeated more than 3 times for 0.5s, then it is considered not compressing
- Added reset CPR on no data from junior/baby manikin and then disconnect on the 11th second
Corpuls
- Added CPR Depth changes handler in C1
- Fixed adequate and max depth not reverting to original values after the manikin is disconnected
- Fixed overlapping lines. Fixed truncating labels.
- Resolved the issue of displaying “Deliver Shock” even when it was unnecessary
- Fixed the issue on Auto Analyse where it does not automatically activate after the pie chart cycle
- Fixed the issue of the metronome turning off
- Addressed the issue of getting stuck with “Select Energy”
- Started improvements on metronome state during switches to and from AED, where OFF state will now change to default and where ON state will remain as previous when both settings are toggled to start metronome automatically
- Set metronome default for both Manual and AED as Adult 30:2 for consistency
- Adjusted the metronome after preShock to ensure the sound is correct for “Adult cont.” or “Child cont”
- Resolved an issue where “Do not touch and move patient” voice prompt activates randomly during CPR phase after exiting and restarting the same monitor, including instances when the monitor was powered off
- Resolved the issue of incorrect buttons (Energy, 100, and 200) appearing in AED
SimConnect
- Resolved the issue with additional monitor not showing the correct state of pleth based on the primary monitor when SimConnect is used
- Fixed removal of available SimConnects on rescan when the bluetooth is disabled
- Updated SimConnect firmware
- Resolved the issue of other monitors crashing when attempting to connect to SimConnect
Scenarios
- ECG, Spo2, Etco2 and RR default visible state changed to off for new scenarios and any existing scenarios stay with the existing behavior of being on
- Changed finger attached to be on by default to match other areas of the app
Facilitator Controls
- Resolved the issue of selected Events in Control not loading after the update on new electrodes
- Added 18 channel configurations for custom Event in Control
- Enhanced the Electrode Placement UI to update based on the connected monitor, displaying either 12 or 18 channels
- Implemented new UI in Quick Placement and Manual Placement
- Enabled switching between Anterior and Posterior views
- Added toggling function for new electrodes in Manual Placement
- Added toggling function for new electrode options in Quick Placement
- Adjusted new UI to be suitable for smaller screens
Defigard Touch 7
- Resolved the issue with Defigard Touch 7 crashing when electrode placement is changed
- Fixed crash from removing 12 leads and pads before scenario starts in Defigard Touch 7
Lifepak 15
- Added ART option in Channel 2 and Channel 3 for the waveform
- Fixed Co2 numeric not blinking when outside of alarm range
Lifepak 20
- Resolved the issue of memory leaks that slow down performance of the iPad
Zoll X / Advanced
- Set Pads as default trace for Zoll X Series and Zoll X Advanced
- Added “Pads” as an option in the Quick Access Key: Lead for both Zoll X Series and Zoll X Advanced
TMS
- Resolved the issue with exported video from TMS not getting the correct RR and Temperature values
- Resolved the issue on ETCO2 and RR showing inaccurate values during the preview
- Fixed issue on NIBP getting hidden when changing parameters
Translations
- Updated The Netherlands translations
Multiple Hardware
- Added disconnecting all connected devices on closing the app
CPR Ventilation Monitor
- Added scaling on ventilation bars based on manikin type or parameter settings
- Added numeric label for max volume based on manikin type or parameter settings
- Included a line for each max volume and set at 90% of the full scale
- Enabled clipping of values greater than the full-scale
CPR Depth Monitor
- Resolved the issue on the monitor with the CPR device crashing upon connection with the Control